Fanatec DD2 won't center on F1 2023
Product: F1 23 Platform:PC Please specify your platform model. PC Summarize your bug Fanatec DD2 with Formula V2 wheel won't center What is your 16 digit Report Code? JJXS-ATSD-SKMK-HMVE Can you...
Forum Discussion
@NunyaFnBizNiz wrote:Product: F1 23
Platform:PC
Please specify your platform model. PC
Summarize your bug Fanatec DD2 with Formula V2 wheel won't center
What is your 16 digit Report Code? JJXS-ATSD-SKMK-HMVE
Can you please provide the name of your current internet service provider? Spectum 400Mb
Which area is the bug/glitch in? Single Player
Steps: How can we find the bug ourselves? Run settings for the DD2. Using the recommended settings for the game provided by Fanatec. All firmware updated to current versions. The wheel always goes to +29 when centered.
What happens when the bug occurs? I crash into the right wall as soon as the game starts.
What do you expect to see? I expect to see the car go straight when the wheel is centered.
Product: F1 23
Platform:PC
Please specify your platform model. PC
Summarize your bug f1 2023 Fanatec DD2 steering wheel won't center
What is your 16 digit Report Code? JJXS-ATSD-SKMK-HMVE
Can you please provide the name of your current internet service provider? Spectrum 400Mb
Which area is the bug/glitch in? Single Player
Steps: How can we find the bug ourselves? Go through the settings for a DD2, use the Fanatec recommended settings for the wheel. When I use F3 to test buttons, the wheel is off center (it shows +28) on the graph). If I enter a session, the car immediately drives into the wall (right), if I don't catch the wheel in time and drive it with the wheel upside down. I have gone through the Fanatec wheel centering and motor calibration and the issue remains.
What happens when the bug occurs? The car drives into the right side wall.
What do you expect to see? To go straight.
My setup is a Fanatec Podium DD2 Podium + Formula v2 rim. The firmware has all been updated to current versions.
Ensure you have done the driver and firmware updates first (I know you said you've done them, but please humour me and check)
- Podium DD1 / DD2 Base: 3.0.3.5 (NEW)
- Podium DD1 / DD2 Motor: 3.0.0.2
- Podium DD1 / DD2 WQR: 7 (NEW)
- CS SW Formula V2(X), V2.5(X): 47 (NEW)
Once you have the wheel registered and updated in the Fanatec Control Panel, close the FCP.
Disconnect the wheel and any additional controllers.
Go into the game and delete any custom controller schema.
Exit the game.
Verify Steam files / EA app
Delete the hardware_settings_config.xml
Start the game (mouse or keyboard). Reconnect the wheel. Head to the controller presets and verify they work okay for what is detected.
Modify the schema and save to a custom schema.
Play.
Thank you for your reply. I followed your instructions and my wheel is still on +28 when centered. It does rotate to 100 both left and right but at center it shows 28 rather than 0.
One quick comment for others who might be following along, the "Delete the hardware-settings_config.xml" line should read "Delete the hardware_settings_config.xml"
I have included a picture of my firmware versions for reference.
@NunyaFnBizNiz wrote:Thank you for your reply. I followed your instructions and my wheel is still on +28 when centered. It does rotate to 100 both left and right but at center it shows 28 rather than 0.
One quick comment for others who might be following along, the "Delete the hardware-settings_config.xml" line should read "Delete the hardware_settings_config.xml"
I have included a picture of my firmware versions for reference.
So in the Fanatec Control Panel there is a wheel centring utility. Do not have the game open and centre the wheel in the utility. It's basically along the lines of physically centre it then click the button to sync the software. Close the panel and start the game. Report back please.
I also edited the typo in the first reply. I also edited the fw version (it was a Fanatec typo in the release note). Also added that I don't have the FCP open when playing (IIRC, not recommended).
I have used the wheel center calibration, no joy unfortunately.
@NunyaFnBizNiz wrote:I have used the wheel center calibration, no joy unfortunately.
So what does it report in FCP?
What is the DOR set to? Try the Fanatec forums for recommended settings and user suggestion.
My CSL-E/CSFWv2 combo is set to SEN AUTO and 360 in FCP and in-game.
Featured Places
