Platforms make rooms separate from house
Whenever I use platforms in my house, the room with the platform becomes separated from the house. If I want to move the whole house, any rooms with platforms are left behind. Also, it seems that the...
Forum Discussion
Apparently it registers the platformed part in a room as a 'separate room' so you can't upload the full room with that platform add on. Or is there a way? Anybody else know anything or if they are working on this to fix it so we can? I'd like to upload some of these bedrooms I made but with the platform on part of the room I can't cause its missing, unless I upload it as like "Bedroom part1 and the platform part as bedroom part 2. Any words or thoughts?
@Elithian87 @FalconSims Hmmmm... the house I'm building has no need for platforms so I have only done experiments with them so far. When I read this post I tried what you mentioned and am not seeing the issue in my experiments to this point. This is what I've tried so far...
I used the home I've been doing platform, ladder and stair combo experiments in. In this 1st floor room there are three platforms of varied heights with stairs and ladders. One of the platforms is dragged downward for a sunken room effect, I think 2-3 steps downward. When I click the side of the large room that contains the platforms within it it highlights as one room, though all of the platforms look like separate areas. However...
When I choose to save this as a room... it does save the room with all three platform areas intact, though it does delete the ladder and stair parts in all of them...
Then I went to a different lot and placed the room on that lot. All of the platforms and room placed fine...
But I did find that above all of the platforms the ceiling was missing when placed.
I was able to plunk on a clunky huge roof... But even with the roof stuck on the holes remained.
So I did the trick I normally do to fill in a hole in the ceiling like this. Use the room or wall tool to make a room over the holes. This will create a floor that will become the ceiling for the hole area. Then just delete the walls on these new temp rooms. Also go up a level and delete the ceilings those rooms made or they'll be hanging around up there.
In your cases I'm assuming your rooms are different in some way(s). Can you provide screenshots of your lot and issue?
@SheriGR My issue is with moving the house. The platforms don't move along with the rest of the house. And my ceiling issue happens with any room in a house with platforms in it anywhere. I usually have to move the house and then move it back in order for the ceiling to register.
Are you selecting it as a total house then changing it... Wait that wouldn't work. How are you saving it as a room with the.. How are you saving it with the platforms of it just being a room?
@Elithian87 This is the method I use to save as a room: https://sherigr.com/tutorials/saving-room-to-sims-4-library-gallery/
@Elithian87 Hmmm... If your room is set up anything like @FalconSims 's in those screenshots, I think I may have a clue what the difference is between this and my test on my lot. My platform areas were all within the room and not touching any orf the room's outer walls.
When I dragged the platform area to intersect with the wall it deleted the wall. I had to then re-draw the wall, and the room no longer recognized that new wall section as part fo the rooms exterior wall (when you click an exterior wall it does not highlight that wall section:
So, in that case if I saved that room to my library, upon placement of the room the platform area and wall piece are deleted:
Plus, as in the case of the other test, the ceilings are deleted when the room is placed:
I could see parts of this dynamics as possible oversights and a bug, because this will not allow a save any room with a platform against the wall if this happens with all types of platforms that are against a wall. I don't see any reason why it would be by design/intended for the ceilings to delete when the room is placed either.
This reminds me of making a 'sunken room' area previously - that we needed to make sure there was at least one tile between the sunken area (deleted floor combined with foundation) and the wall to get it to save with the lot, though it wouldn't save with the room by itself. But even then I don't remember the ceiling deleting. Now the sunken platform area will save with the room, but not if it touches the room's exterior wall, it seems?
Edit: I tested and the same thing happens with the wall, saving the room to the library and placing with a raised platform.
- @SheriGR I will save it to my gallery, but I’m just trying to move my house to another area on my lot not place it on a new lot from my library. My ID is kyrieann12 and you may have to check custom content, as I have some sim made paintings in my house.
Hi! I am having this problem at the moment and wondered if you could talk me through how you fixed the problem. I am creating a bathroom and I'm using the triangle platform next to my bath (which is angled in the corner). As this platform removes the walls, when I rebuild them these walls, and the platform, don't count as being apart of the same room. Therefore, when I go to upload this to the gallery, the lighting is bad and my bathroom is missing a corner and all the shelves and stuff that is apart of that corner and platform ensemble is missing. I have attached photos incase this helps describe what I mean.
- @tyira1
Hi, there
Is there a ceiling in this triangular area? Or is there a ceiling there only? Areas with ceilings and areas without ceilings do not count as one room. Also, places with different foundation heights are not counted as one room.
Please check.
If there is nothing wrong with either, you may want to start a new thread. This thread is 2 years old and may be locked.
Hope your help.
EA_BarryCommunity Manager
This is an old thread, we prefer if you could make a new thread regarding your issue/feedback.
Thread locked.
Thanks.
